The practice of using veneers is popular in America even though this procedure is not widely taught in the dental schools. These procedures are usually successful, but caution needs to be exercised that they are used in the procedures of diagnosis. Other diagnostic options include direct bonding, traditional orthodontics, bleaching and esthetic recontouring. The information here will guide you through the no prep veneers Houston procedures.
The first step is whereby the veneers are tried each at a time with no try-in paste so as to make it easy for evaluation of the fit for the persons units. After all the veneers have been tried in, and the fit confirmed, the units can then be tried in at once to check the contacts. At this stage, they are typically tried restoration with the try-in cement to ensure that they stay in place. After the restorations are all in place, the patient is given a mirror so that they can also look at them.
The try-in cement is then made water soluble. The importance of this procedure is to ensure that all the internal elements that the veneers may leave behind can be cleaned up easily. There is usually a pumice prepared before which is them mixed with some liquid consepsis which is used to clean the teeth. After this, the teeth will then be dried using air.
The procedure that follows this is etching of the teeth with phosphoric acid of 37% concentration for about 15 seconds. This is then rinsed off, and the teeth are left to dry. The picture that one gets, in this case, is frosty that is associated with the etching enamel. The dentist will then prepare a thin layer of a scotch bond adhesive and places it using a micro brush.
The dentist then takes the veneer cement and applies it on the veneer and places it on the tooth. Extra cement is left to remain visible, and if it cannot be seen, the veneer is removed, and then more cement is added until he is sure that it can be seen on the margins. This procedure is repeated for all veneers.
In step five, the dental assistant takes the LED emetron curing light and then holds it roughly 5-7 mm from the extra cement in the gingival border and cures it for almost five seconds while waving the light backward and forward. He aims here is simply getting the cement to its gel state without curing it completely, because the more the clean is done, the less the clean up with the handpiece later on.
Upon the cleaning up of the gingival margin, light is placed on its tissues and margins halfway in order to complete the curing process and to hold everything together in place. Flossing is then done in order to clear the excess cement before it cures completely.
After the extra cement is done away with, the last curing is completed. The centrals get placed first and simultaneously since they are so important to the general success of the esthetic case.
The first step is whereby the veneers are tried each at a time with no try-in paste so as to make it easy for evaluation of the fit for the persons units. After all the veneers have been tried in, and the fit confirmed, the units can then be tried in at once to check the contacts. At this stage, they are typically tried restoration with the try-in cement to ensure that they stay in place. After the restorations are all in place, the patient is given a mirror so that they can also look at them.
The try-in cement is then made water soluble. The importance of this procedure is to ensure that all the internal elements that the veneers may leave behind can be cleaned up easily. There is usually a pumice prepared before which is them mixed with some liquid consepsis which is used to clean the teeth. After this, the teeth will then be dried using air.
The procedure that follows this is etching of the teeth with phosphoric acid of 37% concentration for about 15 seconds. This is then rinsed off, and the teeth are left to dry. The picture that one gets, in this case, is frosty that is associated with the etching enamel. The dentist will then prepare a thin layer of a scotch bond adhesive and places it using a micro brush.
The dentist then takes the veneer cement and applies it on the veneer and places it on the tooth. Extra cement is left to remain visible, and if it cannot be seen, the veneer is removed, and then more cement is added until he is sure that it can be seen on the margins. This procedure is repeated for all veneers.
In step five, the dental assistant takes the LED emetron curing light and then holds it roughly 5-7 mm from the extra cement in the gingival border and cures it for almost five seconds while waving the light backward and forward. He aims here is simply getting the cement to its gel state without curing it completely, because the more the clean is done, the less the clean up with the handpiece later on.
Upon the cleaning up of the gingival margin, light is placed on its tissues and margins halfway in order to complete the curing process and to hold everything together in place. Flossing is then done in order to clear the excess cement before it cures completely.
After the extra cement is done away with, the last curing is completed. The centrals get placed first and simultaneously since they are so important to the general success of the esthetic case.
About the Author:
To benefit from no prep veneers Houston dental patients are advised to use this excellent clinic. Make an appointment now through this website http://tophoustoncosmetic.dentist.
No comments:
Post a Comment